QS – read user manual online or download in PDF format. Pages in total: Preface This document is intended to assist the service technician in the operation, maintenance and repair of the QS Series 64 Voice Synthesizer/ Controller. QS7/QS8 Reference Manual 1 2 QS7/QS8 Reference Manual Table of Contents Contents 1: Setting Up 7 Unpacking and Inspection 7 AC Power 7 Line.

Author: Doulrajas Dakinos
Country: Russian Federation
Language: English (Spanish)
Genre: Spiritual
Published (Last): 3 April 2008
Pages: 476
PDF File Size: 1.44 Mb
ePub File Size: 6.82 Mb
ISBN: 957-1-37395-760-9
Downloads: 38443
Price: Free* [*Free Regsitration Required]
Uploader: Zululmaran

Please note that there are only Mixes numbered 00 through 99 in each Bank. Chapter 2 Choosing programs in a mix In this section, we will choose Programs for the 1 6 channels in a Mix, for playing back tracks from a MIDI sequencer. These should be low-capacitance shielded cables with a stranded not solid internal conductor and a low-resistance shield.

It’s basically the same as the QS6. Navigating In Effects Edit Mode A quick and useful way to make Effect changes in a Mix, therefore, is to simply choose whole new Effects from among those that are immediately available.

Your own ears will have told you this by now, of course, since lots of the presets in a QS use the effects to some degree. This setup of parameters can be stored so that you can get back to it instantly at laesis touch of a button. This manual also for: Polyphony – 64 Voices with dynamic voice allocation. This allows the QS to send data to the sequencer for recording, and play back data from the sequencer.

Replace only with the same type or equivalent type recommended by the equipment manufacturer. So, when you store a Program, you store its Effects Patch along with it. A delay of 4. The Chorus effect is achieved by taking part of the signal, slightly delaying it, and then slightly detuning it as well. Manuall room with soft surfaces such as carpet will produce a reverberant sound kanual much less high end alexis than a room with hard surfaces.


R6 and R24 R85 and R80 R72 and R71 help match impedances as well as current limit and resistively isolate the signal before output.

Alesis QS7 Reference Manual

Sends 2 and 3 have Pitch modules preceding Delay modules, which are then routed to Reverb 1. Send 3 reverb low decay A Program consists of up manuall four sounds. The product should only be connected to a power supply which is described either in the operating instructions or in markings on the product.

All banks can be stored to by the user, and it comes with additional Programs and Mixes pre-stored. For more information, see page Although the card can physically be used in either slot, once a Program is stored using a Sound on a card it expects to find that card in the identical slot it was in when the Program was stored.

In other words, if you have two SRAM cards k each, capable of storing up to 4 banksyou will have 4 banks available on each card for a total of 8 banks; alesiz below the maximum. These buffers are retained when moving between Program Mode and Mix Mode, making it easy to search for a suitable location to store your newly created Manuwl.

By connecting an expression pedal to the [PEDAL 1] jack, you can use the pedal to change the volume or tone or some other quality such as reverb depth or vibrato speed of the sound, if the Program is edited to use the pedal s. Obtaining Repair Service A description of the problem. Part 8 Modulation Destination Page 2 Select from the following modulation destinations. However, if the recorder is using the Flere is a chart listing the various drum samples in their respective groups.


No numbers are displayed in MIX mode. Send 2 resonator decay Many acoustic instruments, such as acoustic guitars, sound brighter when you play I IF. This makes it possible to have the signal from the Pitch or Delay sections, or the direct effect send in any combination or amount.

Alesis QS user manual – – Solve your problem

Level 00 to 99 Page 1 0 This is the overall output level of the envelope. Level Setting for Each Program The Level function press [60] of Mix Edit is used to control several parameters that deal with the audio output of the selected channel. Many variables are available in this scheme. Setting modulation to 00 turns off the modulation source. Insert a flat blade screwdriver into the slot.

Program or Effect parameter that you want. But it has more! This section lets you manuall the sound to one of the effect buses for processing see Chapter 7 for more information on editing Effects.

When this parameter is set to 0, velocity will have no affect on the filter. The DAC outputs are balanced and are routed through differential amplifiers to the unit’s output jacks, via the analog output circuitry See Section 2. Your phone number manyal e-mail, if you have it.

The model OC cable is 5 meters long and is the maximum length recommended. Setup and Connections on page Although this effect is not found in nature, it works great for modern drums, percussion, and any quickly repeated, transient source.