– wiring (Denso) for Wingroad with Y12, Electrics. Frame / Series, Y12 / Y12, body, W (wagon), engine, HR15DE (HR15DE engine), drive, 2WD. HR15DE engine model. flexible wires and anchors, work properly. If loose parts, deterioration, cuts .. to any components or wiring of the supple- mental air . HR15DE engine torque curve. Achieves plentiful low-end torque extending through mid-to-high engine speed. MR20DE engine torque curve. liter engine.
|Published (Last):||24 May 2012|
|PDF File Size:||17.51 Mb|
|ePub File Size:||20.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
After the vehicle stops, the engine stalls. When disconnecting ECM harness connector Aloosen C it with levers as far as they will go as shown in the figure. Thus, they differ from ECM terminals voltage signal. A few seconds after turning ignition switch OFF [Ignition switch: Permission Reusing this file.
Fully released Accelerator pedal: Exhaust valve timing control does not function. After warming up, idle the engine More than seconds after starting engine? This page was last edited on 9 Marchat After warming up, idle the engine Heater fan switch: Below 3, rpm after the following conditions are met.
HR15DE Wire Harness – Engine – Tiida – Nissan
Engine coolant temperature will be determined by ECM based on the following conditions. This file contains additional information such as Exif metadata which may have been added by the digital camera, scanner, or software program used to create or digitize it. P P Detected items Intake valve timing control Exhaust valve timing control Engine operating condition in fail safe mode The signal is not energized to the intake witing timing control solenoid valve and the valve control does not function.
Below 3, rpm after the following conditions are met – Engine: I, the copyright holder of this work, hereby publish it under the following licenses:.
From Wikimedia Commons, the free media repository. When ECM detects the hr155de valve is stuck open: Power generation voltage variable control: ECM controls the electric throttle actuator by regulating the throttle opening around the idle position. If the file has been modified from its original state, some details such as the timestamp may not fully reflect those of the original file.
Wiring for – Nissan TIIDA/TIIDA LATIO C11 | Japan sales region, ,
Revving engine from idle to 3, rpm quickly after the following conditions are met – Engine: The ECM regulates the opening speed of the throttle valve to be slower than the normal condition. ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.
The engine speed will not rise more than 2, rpm. Fully depressed — — 0.
240 – wiring (Denso) for Nissan Wingroad Y12
You may select the license of your choice. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.
Not being turned Steering wheel: The timestamp is only as accurate as the clock in the camera, and it may be completely wrong. OFF Air conditioner switch: OFF] — — [Engine is running]? Average voltage for pulse signal Actual pulse signal can be confirmed by oscilloscope. Slightly gr15de [Ignition switch: Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show the specification data in spite of widing ignition timing not being adjusted to the specification data.
Before measuring the terminal voltage, confirm that the battery is fully charged.
When the fail-safe operations for both self-diagnoses occur, the MI illuminates. The following other wikis use this file: Vehicle has traveled after MI has turned ON. The signal is not energized to the exhaust valve timing control solenoid valve and the valve control does not function. More than 1 second after turning ignition switch ON [Engine is running] [Ignition switch: ECM is located in the engine room left side near battery.
The test limit is a reference value which is specified as the maximum or minimum value and is compared with the test value being monitored. After warning up, idle the engine? ECM controls the electric throttle control actuator by regulating the throttle opening to 20 degrees or less.
The item is indicated, but not used. This licensing tag was added to this file as part of the GFDL licensing update.
ON Compressor operates — [Ignition switch: ON] — — [Ignition switch: Therefore, when electrical controlled throttle and part of ECM related diagnoses are continuously detected as NG for 5 trips, ECM warns the driver that engine control system malfunctions and MI circuit is open by means of operating fail safe function.